The screen developer goes directly to the right or left of the clean sink, and the screen cleaner goes directly to the right or left of the dirty sink. dip tank solution) in it, and one for developing screens with clean water in it. Why two? One for cleaning screens with de-inker/emulsion remover (a.k.a. Having two dip tanks can maximize your efficiency in a dark room and keep things much cleaner. The better your filter setup the better off your pipes and the earth will be. Most shops that I know don’t take this as seriously as they should, and mainly focus on getting the particulate and ink residue out of the water before sending it down the drain. This means your filter needs to be pretty high tech. Technically, most water collection areas don’t allow any colored water to go down the drain. But if you are going to be cleaning ink in it, it needs a more advanced filter. Your clean sink can be filtered using screen mesh, 110, 125, and 156 mesh. Ensure your sinks are filtered to avoid particulates from going down the drain. The cleanout sink’s cleanliness is much less important than the washout sink. This is where you finish the deinking process and reclaim the screen. You want the other area to be your cleanout sink. This is your washout sink, where you degrease screens and washout your images. Ideally, you should have two sinks, or a sink and a fluid cleaning table that has access to water and a drain. Two separate sinks for washout and cleanout If they must be in the darkroom, make sure to add some type of divider or strong ventilation to keep the moisture away from your screening area. The easiest way is to put your washout and cleanout screens directly outside the darkroom. Because moisture is a problem, it’s a good idea to keep your water and your screen area as segregated as possible. Ideally, you want your darkroom to be 35-40% humidity. Wet screens breakdown and don’t hold detail well. A low humidity space, free of dirt and dust Here’s what you need to create the right darkroom conditions: 1. It’s where the magic of making good screens happens-and good screens equal good prints. I like to think of the darkroom as the “clean room” of screen printing. Your darkroom, of course, is very important to this process. You’ll see that in this example, it’s been organized to facilitate a consistent, one-directional flow. Here’s what your finished darkroom could look like. Things should flow from point A to point B without resistance in a logical manner. You can see how he has arranged the shop flow in the production area and the screen room. Here are some shop layouts that Dan from Forward Printing did as a consulting project for one of our ROQ clients, Tipsy. The screens then make their way to be cleaned and back to the beginning. Art, screens, and shirts come into the press get printed on the press go into the dryer come off the dryer and shirts and the dirty screens that printed come out the end. Per Dan, the key is flow. Ideally, your process should keep things flowing in a single direction, uninterrupted. Dan from Forward Printing has helped me (as well as many of Ryonet’s Screen Experience students and customers) learn the best practices of how to set up a solid screen printing production workflow. Once you have the big ticket items out of the way, it’s time to think about production. If you do not have the instruction manual for your computer, if you add the make and model of the printer in the Comment section, I may be able to locate the manual for you online.Below is an excerpt from my book, “ Made to Make It: A Guide To Screen Printing Success.” Learn helpful tips and tricks on how to run a screen printing business. I hope you have the instruction manual for your computer so you can read through it and follow the instructions for printing. If you use Windows, once the document/whatever you wish to print is selected, click or tap on FILE (upper left of the window), click or tap on PRINT, and follow the on-screen steps. I don't use a MacIntosh, so if you have a Mac, I cannot provide those steps for you. Once you have chosen the document, image, whatever to print from your computer, you should be able to follow the steps to print. Plus, if the connection is via WiFi, the computer must be connected to the Internet. There must be adequate ink in the printer, and paper. The computer must be powered up and the printer power must be on. Plus, you need to have your printer connected to your computer, either by direct connection with a cable, or via WiFi connection. You need to have the latest driver for your printer installed on your computer.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |